Rowe r86 jukebox pdf#
Rowe r86 jukebox update#
Rowe r86 jukebox manual#
Rowe r86 jukebox software#
Rowe r86 jukebox series#

To confirm that the software downloaded correctly, execute show system and check the Firmware revision line.ДЇor information on primary and secondary flash memory and the boot commands, see 'Using Primary and Secondary Flash Image Options' in the Basic Operation Guide for your switch. A switch covered in this guide (with multiple configuration files), also uses the current startup-config file.ДЇor more information on these commands, see 'Rebooting the Switch' in the Basic Operation Guide for your switch. NOTE: If an error occurs in which normal switch operation cannot be restored, the switch automatically reboots itself, and an appropriate message is displayed after the reboot.Д«oots from the flash image and startup-config file. (See 'Getting Documentation From the Web'.)

To find more information on the cause of a download failure:Д®xamine the messages in the switch's Event Log by executing the show log tftp command from the CLI.ДЇor descriptions of individual Event Log messages, see the latest version of the Event Log Message Reference Guide for your switch, available on the HP Switch website. One or more of the switch's IP configuration parameters are incorrect.ДЇor a UNIX TFTP server, the file permissions for the software file do not allow the file to be copied.ДЄnother console session (through either a direct connection to a terminal device or through Telnet) was already running when you started the session in which the download was attempted. This can also occur if the TFTP server is a UNIX machine and the case (upper or lower) for the filename on the server does not match the case for the filename entered for the Remote File Name parameter in the Download OS (Operating System, or software) screen. Incorrect name specified for the Remote File Name parameter, or the specified file cannot be found on the TFTP server. Incorrect or unreachable address specified for the TFTP Server parameter. Some of the causes of download failures include: When using the menu interface, if a TFTP download fails, the Download OS (Operating System, or software) screen indicates the failure (see Example: of message for download failure).Д®xample: of message for download failure Hp Procurve 2610 Firmware Download NOTE: If your TFTP server is a UNIX workstation, ensure that the case (upper or lower) that you specify for the filename is the same case as the characters in the software filenames on the server.ДЇor troubleshooting information on download failures, see Troubleshooting TFTP download failures. If VLANs are configured on the switch, determine the name of the VLAN in which the TFTP server is operating.Дetermine the name of the software file stored in the TFTP server for the switch (For example, E0820.swi). Obtain the IP address of the TFTP server in which the software file has been stored. The TFTP server is accessible to the switch via IP.Д«efore you use the procedure, do the following: The switch is properly connected to your network and has already been configured with a compatible IP address and subnet mask. (The software file is typically available from the HP Switch Networking website at. In this case, use the boot ROM console to download a new image to primary flash.ДЄ software version for the switch has been stored on a TFTP server accessible to the switch. In the unlikely event that the primary image is corrupted (which may occur if a download is interrupted by a power failure), the switch goes into boot ROM mode.

In most cases, if a power failure or other cause interrupts a flash image download, the switch reboots with the image previously stored in primary flash. The switch configuration is contained in separate files that can also be transferred.

NOTE: Downloading new switch software does not change the current switch configuration. Until a reboot occurs, the switch continues to run on the software it was using before the download. Switch software that you download via the menu interface always goes to primary flash.ДЄfter a software download, you must reboot the switch to implement the new software. Other terms sometimes include Operating System, or OS.

Rowe r86 jukebox manual#

NOTE: This manual uses the terms switch software and software image to refer to the downloadable software files the switch uses to operate its networking features. For more information, see the support and warranty booklet shipped with the switch, or visit and click on software updates. HP Switch periodically provides switch software updates through the HP Switch Networking website.

Rowe r86 jukebox update#

(ProCurve Switches 2626/J4900A and 2650/J4899A) When updating from Software versions H.07.31, H.07.32 or H.07.40 to H.08.100 or later, you must first update and boot the switch using the version H.08.98.

Rowe r86 jukebox series#

View online or download Hp ProCurve 2610 Series Advanced Traffic Management Manual, Installation And Getting Started Manual.

Rowe r86 jukebox pdf#

Hp ProCurve 2610 Series Pdf User Manuals.